Background

OOPS Observation Processing Flow

The flow of H(x) computation and QC filters application in OOPS is shown in the figure below.

../../../../_images/observer_flow.png

Fig. 14 Flow chart for computing H(x) and running QC filters

The Observer calls the preProcess method of ObsFilters before the loop over time steps. After the loop, it calls the priorFilter and postFilter methods just before and just after calling the simulateObs method of ObsOperator. The observation filters are very generic and can perform a number of tasks, but mostly they are used for quality control.

In variational data assimilation, the above flow happens inside of the observation term of the cost function (Jo) evaluation.

Observation Filters

Observation filters have access to:

  • Observation values and metadata

  • Model values at observations locations (GeoVaLs)

  • Simulated observation value (for post-filter)

  • Their own private data

Most filters are written once and used with many observation types; several such generic filters already exist and are decribed below. Filters applied to observations from a specific ObsSpace need to be listed in the observations.observers.obs filters section of the input YAML configuration file, together with any options controlling their behavior. Example:

observations:
  observers:
  - obs space:
      name: AMSUA-NOAA19
      obsdatain:
        engine:
          type: H5File
          obsfile: Data/obs/testinput_tier_1/amsua_n19_obs_2018041500_m.nc4
      simulated variables: [brightnessTemperature]
      channels: 1-15
    obs filters:
    - filter: Bounds Check
      filter variables:
      - name: brightnessTemperature
        channels: 1-15
      minvalue: 100.0
      maxvalue: 500.0
    - filter: Background Check
      filter variables:
      - name: brightnessTemperature
        channels: 1-15
      threshold: 3.0

An alternative to using obs filters is to specify the sequence of filters explicitly using the obs pre filters, obs prior filters and obs post filters options. Further information on that can be found in the following section.

Order of Filter Application

The order in which filters are run can be specified in two ways:

  • Determine the ordering automatically based on the data required by each filter.

  • Specify the ordering explicitly.

Automatic filter ordering is requested using the obs filters option. By default, all filters that do not require access to GeoVaLs, ObsDiagnostics or the HofX vector are run first, in the order they are listed in the obs filters section in the YAML file. Subsequently, GeoVaLs are calculated and all filters that require access to GeoVaLs (so-called prior filters) are run. Finally, the observation operator is applied, producing the HofX vector and possibly some ObsDiagnostics, and all filters that require access to these quantities (so-called post filters) are run. It is possible to force a filter to be treated as a post filter and thus defer its execution until after the application of the observation operator by setting the defer to post option to true.

Explicit filter ordering is requested using the obs pre filters, obs prior filters and obs post filters options. Filters that appear in the obs pre filters section will be run before the GeoVaLs are requested; those in the obs prior filters section will be run after the GeoVaLs have been requested and before HofX is produced; and those in the obs post filters section will be run after HofX has been produced. To request explicit filter ordering, one or more of these sections must be specified. The filters in each section will be run in the order in which they are specified in that section. Checks are run on the filters to ensure they are not requesting data that are not available. For example, a filter in the obs pre filters section cannot request HofX data. If such a request is made then an exception will be thrown.

It is not possible to mix automatic and explicit ordering; an exception will be thrown in that case.

Examples

The first example uses the automatic determination of filter ordering. The Thinning filter will be run after the Background Check because its defer to post option is set to true. If that was not the case, the Thinning filter would be executed before the Background Check, since the former does not need access to the HofX vector, whereas the latter does.

obs filters:
- filter: Background Check
  filter variables:
  - name: airTemperature
  absolute threshold: 2.0
- filter: Thinning
  amount: 0.5
  defer to post: true

The second example uses explicit specification of filter ordering. As above, the Background Check and Thinning filters are run after HofX has been produced. There is also a Variable Transforms filter that runs at the pre-filter stage.

obs pre filters:
- filter: Variable Transforms
  Transform: WindComponents
obs post filters:
- filter: Background Check
  filter variables:
  - name: airTemperature
  absolute threshold: 2.0
- filter: Thinning
  amount: 0.5

Derived Variables

Some filters need to create new or modify existing ObsSpace variables. For example, the Variable Transforms filter may create new variables representing wind velocity components computed from measurements of the wind speed and direction. Other filters may want to correct measurements or metadata loaded from the input file.

It is important to note that filters should never modify variables from the ObsValue group or add new variables to that group: otherwise initial and postprocessed measurements could not be distinguished, which would harm traceability. Instead, filters may create or modify variables from the DerivedObsValue group; any such DerivedObsValue variable must be declared in the yaml as described in observations. The ObsSpace treats all groups with the Derived prefix in a special way. Each member function used to access existing variables, such as get_db(group, name, ...), checks first if a variable name exists in the group "Derived" + group and if so, it retrieves that variable; if not, the function looks for the variable name in the group group. As a result, variables from groups with the Derived prefix effectively “overshadow” corresponding variables from groups without that prefix. In the rare cases where it is important to access the original variables rather than their derived counterparts, ObsSpace member functions should be called with the skipDerived argument set to true.

There is no strict rule forbidding modifications to variables from other groups such as MetaData. However, for clarity, it may be a good idea to avoid modifying metadata loaded from the input file and instead store any corrected versions in variables from the DerivedMetaData group.

Note that any variables from the DerivedObsValue group that are to be assimilated should be included in the obs space.simulated variables list as well as the obs space.derived variables list (see observations). If these variables do not exist by the time the last filter finishes execution, an exception is thrown. (In contrast, variables from the obs space.observed variables must exist already when the first filter starts execution.)

Observation Errors

Use the following variable groups to refer to estimates of observation errors of simulated variables valid at specific stages in the execution of a JEDI application:

  • ObsError: initial values loaded from the input ioda file.

  • ObsErrorData: up-to-date values (set by one of the preceding filters).

  • EffectiveError: final values obtained after execution of all filters. This group does not exist while filters are running, but is present in the output ioda file.

All these values represent standard deviations (square roots of variances).